Corner connection of the countertop in the kitchen

The need to connect the elements of the kitchen countertop is due to the peculiarities of rooms with an L-shaped configuration. Many people are confused about how to connect the countertop to form a single, straight structure.

kitchen countertop joint — When the design of the room requires the installation of corner furniture or the total area does not allow to put the work surface in full length, the parts of the product are joined.

The main thing is that the product looks without joints. There are several technologies that allow you to combine parts into a single composition.

kitchen countertop joint photo — The joint of the countertops should be tight, with a minimum gap between the ends of the countertops.

Content Hide

How can you connect the tabletop at 90 degrees
How to connect two countertops to each other without a joint
Video: gluing tabletops with Euro saw
Photo 50 design options for the junction of the countertop in the kitchen

How can you connect the tabletop at 90 degrees

The lifespan of your kitchen worktop will depend on a strong and secure fit. If the area allows, you can dock the tabletop elements at right angles. To resolve this situation, use one of the appropriate methods.

kitchen countertop joint ideas — It is difficult to achieve a smooth joint if the end of the countertop has an oval and rounded front edge.

Trapezoidal detail

Implies use between two rectangular pieces of a trapezoidal piece. This creates an additional plane of the facade at a flat angle in relation to the rest of the details. This corner version has two joints.

kitchen countertop joint trapezoid — A worktop segment is essentially a top table for a segmented base cabinet.

You can make a trapezoidal segment yourself or purchase a finished product based on measurements in your own kitchen. Most manufacturers offer such elements with a laminated surface. The only drawback of this purchase is the limited choice in terms of shades and sizes.

kitchen countertop joint trapezoid photo — The edge of the segment can be straight or semicircular along the front.

The best solution would be to collect the trapezium from standard slabs sixty centimeters wide. It should be borne in mind that in this case, an ugly joint will turn out near the wall. You can create a comfortable worktop without seams if you install the element to the wall a couple of centimeters above the work plane. This will avoid this problem. The resulting shelf will serve as a place for placing detergents or other items on it.

kitchen countertop joint trapezoid ideas

countertop joint in the kitchen corner trapezoid

worktop joint in the kitchen trapezoid ideas photo

kitchen countertop joint trapezoid photo ideas

Eurostack

Allows you to create a perfect seamless connection. This method requires the use of a piece made with a milling machine. If the ends are made correctly, after assembly the surface of the gap will not be visible.

euro joint worktops in the kitchen — To implement this method, the butt end and the edge of the table top are cut along a curved line of the same diameter.

A design made in a similar way will look neat without protrusions. In this case, one part is machined from the end, on the second the longitudinal edge is ground.

euro joint countertops in the kitchen photo — This method allows you to close the countertops almost perfectly, and the use of a sealant allows you to mask and protect the joint from water.

In the process of technology, how to connect the tabletop, difficulties may arise regarding the cut along the entire length - it must be straight, gradually transforming into a corner. It is necessary to walk on both parts of the cuts with a sealant. It is not recommended to install a textured product in this way, otherwise the connecting places will stand out strongly.

euro joint countertops in the kitchen ideas

euro joint countertops in the kitchen photo ideas

T-shaped profile

Here, the connecting sections are closed from above with a profile. It is imperative that such a bar together with the ends must be treated with a sealant. This technology has an advantage over the Euro saw. Often, countertop elements are joined at the sink located in the corner.

When joining the tabletop using a T-shaped aluminum profile, the lock fasteners are not cut out, the seam is closed with a bar.

Thanks to the aluminum profile, water does not penetrate the material. Therefore, the plank does not rust.

This connection is more practical than Eurozapil.

The advantage of this method is also:

the ability to use next to a gas stove;
suitable for installation on uneven surfaces;
allows you to close the gaps even with inaccurate joining.

How to connect two countertops to each other without a joint

The first step is to prepare the sections for the tightening elements. Then you need the following:

Plank installation. Attach it to the cut, then screw it with self-tapping screws;
The cracks of the countertop, the ends must be smeared with silicone sealant;
Then you can already connect the elements to each other;
The clamp is placed directly into the grooves. On the opposite side of the nut, there will be a tightening head, under which washers are placed;
Next, tighten the nuts with a wrench, tightly pulling the countertops canvases;
The clamps must be pulled crosswise.

The process should be done slowly. Whichever method is used, it is important to pay attention to waterproofing, which prevents moisture from entering between the ends. As you can see, the joining of the countertops at an angle of 90 degrees can be done independently.

corner joint of the countertop in the kitchen — Experts recommend sealing grooves and blind holes with sealant to reduce the risk of moisture penetrating inside.

Joining the worktops using functional strips ensures a high-quality docking. Performing the screed correctly, as a result, you can get a structure that will last more than one year.

Thanks to the use of an aluminum profile, the gap is completely closed.

Another option for joining tabletop elements is to fix the ends with silicone sealant without using a strip. It is enough to fix the ends with silicone sealant. The planes need to be pressed well, removing excess funds.

With euroform, the ends are obtained with an allowance of a few millimeters. Because of this, the planes of the countertops will not completely adjoin. To make the gap not noticeable, you can hide it under the furniture plinth.