The procedure and rules for cleaning the hood from fat
Taking care of clean kitchen parts and a hood, among other things, saves you from many unpleasant formations. In the process, mistakes are made that affect the further operation of the device and personal safety.
By preparing for each step, from start to finish, avoid the trouble.
Preparatory stage
Work starts with your own safety. Disconnect the hood from the power supply.
Next, disassemble the device:
- The cover is removed from the grooves, the latches snap off;
- The filter is removed;
- The pipe leading to the vent is removed;
- The air filter is taken out;
After disassembling, proceed to wash. All parts can be cleaned, including the body.
Cleaning with household chemicals
Before the process, get the instructions for using the hood. Find a cleaning point and make sure that there are no products or components that cannot be used before cleaning the hood in the kitchen from grease.
Note! Household chemicals in use imply their own protection against chemicals. Make sure you have rubber gloves with a respirator.
Only after you are fully prepared can you apply a tap cleaner. The alkaline solution perfectly copes with the task of removing grease and particles formed on the filter.
Place the filters in a stainless steel sink and fill with the product for 10 minutes. Finally, rinse well with running water. And ventilate the room.
How to cleanse using folk methods
The condition for cleaning a home hood is to use what is at hand. How to clean the hood from fat with valid folk remedies? Recommended: lemon, ammonia, vinegar and others.
Even with these tools, do not forget about personal safety. For the effectiveness of the action, familiarize yourself with the correctness of the procedure.
Ammonia
Almost everyone has ammonia or ammonia in their medicine cabinet. If not, it won't be expensive to buy. For 3.5 liters of hot water about 50 degrees, 100 milliliters of alcohol dissolves. It is left for several hours for the remedy to take effect. Washed off.
Vinegar and lemon
These 2 products can act separately and together. Lemon juice or the lemon slice itself can be applied to the item, left to stand for a while, and wipe off the dirt.
The same steps are carried out with vinegar, use six or nine percent. If it is possible to use acetic acid, use by diluting with water and applying to the hood. Allow time to react with dirt and wash off.
The recommended waiting time should be at least 20 minutes. At the end of all washing operations, do not forget to wipe dry all the washed parts.
Soda
The component can be used individually for medium to lightly soiled steel gratings. You will need to bring a large container of water to a boil and add soda there, stirring constantly. In this method, soda ash has worked well.
Per 10 liters, half a glass of powder is required. During the boiling process, a grate is lowered into the liquid. Grease and other contaminants are easily separated from the steel. Also, soda can be used in combination with other means and used for other types of grates.
Combined remedy
Strengthening of each component is made by connecting. Similar advice applies to baking soda, soap, vinegar, ammonia, and citric acid.
You need to connect them in the following sequence:
- Take a 5 liter container.
- Add 1 or 2 tablespoons to the water: salt, citric acid and soda.
- 0.5 bottle of peroxide, ammonia, silicate glue.
- 1/2 bar of soap, previously grated on a coarse grater.
- The solution is heated and a filter is placed in it for a couple of hours.
The created solution is applied to various parts of the hood, and it removes grease qualitatively.
Soap
Laundry soap without additives has proven itself well in dealing with dirt. Among soap products, dishwashing gel is perfectly combined with soda. In addition to the fact that the product is effective, it is also carefully cleaned. Fill a large container with hot water and dissolve a quarter cup of baking soda in it.
Then add 1 tbsp. gel for dishes. Stir the liquid. Do not use your hand to do this. The filters are dipped in a saucepan for 20 minutes, rinsed. A similar recipe can be used to clean the hood from fat for heavy dirt, especially if it is made of steel. Efficiency for them is achieved by boiling in solution for 1.5 hours.
Methods for cleaning the hood in parts
To clean the hood in parts, it must be disassembled first. Each part can be cleaned in its own way. It depends on the composition of the material from which they are made and the level of contamination.
The methods can be as follows:
- Soaking.
- Boiling.
- Replacement.
It will not be superfluous to familiarize yourself with the instructions for the device, it usually has a scheme for collecting and disassembling the hood.
Filter cleaning features
In order to find out about cleaning the filter, first disassemble what type it is. May be:
- Coal.
- Fat traps.
There is no need for charcoal filters to find the right recipe or product. Its design consists of plastic, and inside is a replaceable carbon filter. When the cleaning properties decrease, the filter is simply replaced.
The second type of catchers requires a choice of cleaning, they can be presented in 3 variations.
- Made of acrylic. These filters can be cleaned and washed. But their shelf life is short-lived.
- Synthetics. It can be non-woven, synthetic winterizer or special paper. Disposable filters. After use, they do not need to be washed. Discard and replace with new one.
- Made of aluminum. Unpretentious to maintain, configuration items need to be periodically cleaned without choosing one of the above options. All recipes and ingredients can be used with aluminum.
How to clean the mesh
The popularity of mesh washing methods won out: boiling and Coca-Cola. The last option is the safest.To work with it, rubber gloves, a respirator are not worn, and a window is not opened to ventilate the kitchen. It's just that the mesh should be soaked in soda and the contamination will fall away by itself.
The boiling method is more time consuming. To completely immerse the mesh, a large capacity is needed. Make a solution of salt and baking soda and pour it into a container on the fire. Submerge the mesh. If a container of this size is not available, boil each side in turn.
Cleaning the fan and motor
These parts can be washed once every 1-2 years. Before the first time carrying out such a procedure, obtain the instruction manual. The ventilation manufacturer could indicate where the required parts are, how to remove and wash them.
The beginning of the action is to remove the filters, followed by the fastening bolts, the motor with the fan is removed. The fan impeller can be soaked in the detergent solution for a couple of hours. It is strictly forbidden to wet the motor.
Additional Information! Actions in the form of washing the grease trap are prohibited. It may remain intact after cleaning, but catching fat particles will be much worse.
How to clean the case, buttons and inner walls
To work with the case, you need to use soft tools that will not scratch the surface. This applies to both external and internal work. To clean all the components, you can choose combined products.
The body is washed with a sponge dipped in a cleaning solution. And wipe dry. If there is heavy contamination, the gas supply must be shut off. Then cleaning is carried out with shumanite, wiped with a soft sponge and dried.
The buttons and inner walls can be cleaned with special sprays. Or with a replacement for soapy water. The essence of the action: spray on the buttons, give time to act and rinse.
Frequent mistakes
The most common mistakes are based on the fact that cleaning is done quickly.
And in the desire to quickly wash the hood, you can often forget about such moments:
- Turn off the hood from the mains and start parsing;
- Use hard sponges, brushes;
- Use abrasive substances;
- The boil-off method is used for plastic parts;
- Use alkali in cleaning aluminum components;
- Switch on the appliance when it is not dry.
Additional Information! We remind you of safety precautions and good ventilation of the room when working with chemical compounds.
Care Tips and Tricks
One piece of advice that unites the entire list is attention to the cleanliness and operation of the hood.
Detailed description of all important points:
- Clean regularly;
- No more than 2 times in 7 days the body, grille, panel are cleaned; wipe with grease-absorbing napkins.
- Install the appliance correctly;
- Make sure that the gas is not turned on unnecessarily;
- Take time to check your traction. This can be done independently, or by contacting a specialist.
Pay attention to the noise from the kitchen appliance. If there is an increase in noise, an unpleasant smell of fused plastic or a burning smell, make sure that the entire appliance is thoroughly cleaned.
Cleaning different extracts from fat at home is possible using various methods. They can be home and special. Pay attention to the structural features of the hood in the instructions for it.
Also, do not neglect personal protective equipment. Take care of the ventilation of the room.
Video: how to clean a kitchen hood from fat
